Draw and edit
Draw
Choose Point, Line or Polygon from the floating toolbar. Point at a tool to read its name and key: S Select, B Select several, P Point, L Line, A Area, M Measure. Double-click finishes a line or area; Esc returns to Select.
- Snap (the magnet, shown while drawing or editing) takes the nearest corner within about 10 pixels, even where an edge is nearer, so neighbouring shapes share the corner exactly. Further along an edge it takes the edge.
- Trace (the switch beside Snap, or T) makes a new line or area follow the edge of a shape already on the map, corner for corner, so neighbouring parcels, roads and boundaries share their edges exactly. Click near an edge, then move along the outline: the readout says Along the edge with the length and number of points. Click to place them all. Around an area the trace goes the way the pointer goes; Other way round turns it. Move away from the edge to draw straight again. Any shown layer can be followed, including linked Mapplex and Google Sheet layers, and none is changed.
- Right angles: each new segment continues straight or turns 90°. Holding Shift does the same.
- Exact coordinates: type them in the box on the bar (it reads Length or lat, long, Length on a phone, and Lat, long with the point tool) as latitude, longitude, such as
30.05, 31.24. A ring on the map shows where they are before you commit, and the map goes there if they are out of view. Enter places the point, or the next corner of a line or an area.- Paste several lines, one pair a line (corners from a sheet or a deed), and the whole shape is placed at once. An area's first corner given again at the end closes the area. If a line is not a pair of coordinates, nothing is placed and the line is named. Up to 1,000 lines; use Import for a longer list.
- Enter on the empty box finishes the shape, so a parcel can be typed corner by corner without the mouse.
- Written as you have them: decimal points or decimal commas; a comma, a space, a semicolon or a tab between the two numbers; the letters N, S, E and W; degrees with minutes and seconds (
30°02'40"N 31°14'09"E). Latitude comes first unless the letters, or a latitude that cannot be one, say otherwise.
- An exact length: type one number in the same box and press Enter; the next point goes that far towards the pointer. The Units beside it (m, km, mi or ft, or m→km and ft→mi, which switch as distances grow) are shared with Measure and the scale bar, and kept on this browser.
- Finish (Enter) and Cancel shape (Esc) are on the bar too.
On a very long diagonal edge across a wide area, Trace and line Split can place an intermediate point slightly off the edge as drawn on screen.
Select and change a shape
Click a shape to select it: it is outlined in orange and its properties open, and nothing about its shape can change by accident. To change its shape, double-click it, press Enter or choose Edit shape. Then move it, or drag its large corner handles; the small handles between corners add a corner. Esc or Done editing ends that, and the shape stays selected. To delete what is selected, use the bin on the bar above the tools, or the Delete key.
Fill in its fields in the Properties tab of the side panel: change the values, then choose Apply. Changes save with the map (Ctrl S). Below the fields is the shape's position (latitude, longitude), with Copy coordinates.
When shapes overlap, a click selects the one most likely meant: a point or line before an area, and the smaller area before the one around it. Click again at the same spot to go on to the shape around it.
Move around the map
Hold Space and drag to pan, or hold the middle mouse button (the wheel) and drag. Hold V and drag sideways to rotate; the compass resets north. Shortcuts do not run while you type in fields or dialogs.
Measure
The ruler in the toolbar opens Measure distance and Measure area. Click points, then double-click, press Enter or use the check to finish; area also gives the perimeter. Measurements are never saved or added to a layer. Distances and areas are approximate (on the sphere, without elevation).
Select several shapes
Selection works on the active layer, and the map and the data table share it: rows of selected shapes are ticked, and ticking rows selects their shapes.
- Shift + click adds a shape; Ctrl + click (Cmd on a Mac) adds or removes one.
- Shift + drag draws a box. Dragging to the right takes only the shapes wholly inside it; dragging to the left takes every shape it touches. Ctrl + drag removes the shapes in the box.
- Ctrl + A selects every shape the map shows on the layer. Esc clears the selection.
- On a phone or tablet, choose Select several: a drag draws the box and a tap adds or removes a shape.
With one shape selected, the bar shows its name, its length or area, and everything that can be done with it. With several, it shows how many points, lines and areas, their total length and area, and offers Set a value (one field for all of them), Export selection, Zoom to selection and Delete. Setting a value and deleting are one Undo step each. Hidden shapes are never selected. When points, lines and areas are selected together, click one kind's count on the bar for Keep only that kind.
Hints for likely slips
With a shape selected, the bar points out a likely slip as a quiet hint: a line running a little past a crossing (Overshoot · Trim), a line stopping a little short of another (Gap · Extend), or an area overlapping its neighbour by a sliver (Overlap · Clip). A hint opens its tool with the fix in place, to confirm or leave with Esc. A line that runs on past a junction, such as a road past its last side street, or stops farther short than its last stretch, or than its layer's lines are usually drawn between corners, is not taken for a slip. Only the lines of the line's own layer count, as in Audit: a boundary or another layer shown on the map gives no hint. Trim and Extend opened by hand still reach every shown layer.
Shapes that need repair
A polygon that crosses itself shows a repair hint and opens in editing when you select it: drag its corners until the edges no longer cross.
Shapes with islands (holes), several parts or heights are kept exactly as they are. They do not lock their layer; a kept shape's panel says why, and the bar offers what can be done:
- Edit parts: the outline, each island and each part get their own handles. Draw inside an area to add an island, or outside it to add a part; Delete removes the chosen part. Done writes the shape as one Undo step; Cancel leaves it as it was.
- Separate parts: each part becomes a shape of its own with the same fields.
- Remove islands: the area keeps only its outline.
Shapes with heights are never edited here, so their heights are never lost; their fields can still be filled in.
Limits
A map holds up to 100,000 shapes and 250,000 coordinates. An edit that would pass them is refused and says so.